New-buck-corporation 81 Manual do Utilizador

FIREPLACE INSERT & FREESTANDING MODEL 81 NON-CATALYTIC UNIT Buck Stove FEATURES PREPARATIONS INSTALLATION OPERATION MAINTENANCE SAF

OPTION (B) REMOVE DAMPER OR WIRE IT OPEN AIRTIGHT INSULATED CLEAN-OUT BLOCK-OFF PLATE OR DAMPER ADAPTER SEAL TRIM PANELS WITH INSULATION OR HIGH TE

INSTALLATION PROCEDURE (Use a chimney connector or a Listed Direct or Positive Connect) (See Page 8.) POSITIONING HEATER When positioning h

NOTE: Mount top trim panel so that it sits in front of top of side trim panels. 9. Obtain brass trim kit provided with insert kit and slip over top a

CAUTION THE UNIT IS PAINTED WITH A SPECIALLY FORMULATED HIGH TEMPERATURE PAINT THAT CURES DURING THE FIRST TWO OR THREE FIRINGS. YOU MAY NOTICE A S

SECTION III PRE-FAB INSERT INSTALLATION The Model 81 may be installed into any UL listed pre-fabricated fireplace that is large enough to accept it.

Page 13 SECTION IV RESIDENTIAL FREESTANDING INSTALLATION Select an installation location that will give best airflow from front of heat

ALTERNATE FLOOR PROTECTORS MATERIAL Floor Protection: When installing freestanding heater, a floor protector must be use. Floor protection must be 3

Chimney This model is designed for connection to any listed 2100º UL103 HT chimneys and parts. Follow chimneys manufacturer's instructions care

three (3) sheet metal screws or rivets. Next, install an optional New Buck Corporation chimney connector to flue exit of heater. (See Figure 6). 4.

maintaining clearances to ceiling as noted in Figure 7. This will give you center of hole for chimney penetration. 4. After locating center of pe

NOTE: In addition, a connector to a masonry chimney shall extend through wall to inner face or liner but not beyond and shall be firmly ceme

OPTIONAL Figure 8 Close Clearance Installation using: (1) 6" Simpson Dura-Vent single wall chimney con

FINAL CHECK 1. Recheck specified clearances. 2. Remove all foreign material from firebox area. 3. Open primary air draft. NOTE: Plug power cor

CLEARANCES FOR MODEL 81 MINIMUM CLEARANCES TO COMBUSTIBLES FREESTANDING Figure 9 A B C D E

CLEARANCES FOR MODEL 81 MINIMUM CLEARANCES TO COMBUSTIBLES SINGLE WALL CHIMNEY CONNECTOR AND OPTIONAL SHIELDS, MOBILE HOME AND ALCOVE INSTALLATIONS

INSTALLATION OF (OPTIONAL) CLOSE CLEARANCE SHIELDS 1. Center rear close clearance shield with back of stove. Mark rear of stove, using reference h

Page 24 SECTION V FREESTANDING MOBILE HOME INSTALLATION FOR MINIMUM CLEARANCES SEE PAGE 21. Floor Protection: When installing freestanding heater

Page 25 TOOLS FOR INSTALLATION Drop cloth, 3/32" Metal drill bit, 5/16" magnetic socket chuck adapter, 5/16" wrench (box or socket) or

3. Place unit on pad making sure minimumum clearance specifications are met. For minimum clearance to combustibles (See Page 22). 4. Lightly m

Ceiling Exit (Using Close Clearance Listed Chimney) 1. Suspend a plumb bob from ceiling above unit so that weight is hanging in center of flue exit

TABLE OF CONTENTS Wood Stove Description ...

(a) Chimney pipe is 3' higher than roof at point where it penetrates roof. (b) Chimney pipe height is at least 2' higher than any

4. Place crumpled pieces of newspaper in stove. Light it and close door. Ensure that stove draws properly through primary draft. 5. Check for smo

The chimney and chimney connector should be inspected once every two months. Any build-up of soot should be removed to prevent risk of a chimney fire

BUILDING A FIRE 1. Open door. 2. Open primary air control located on right side of stove under hearth. (See Page 25, Figure 14). To close, push al

ROOM AIR BLOWER OPERATION Your heater is equipped with a room air blower. For operation and wiring (See Figure 14). For your convenience, your heat

SECTION VIII TROUBLESHOOTING PROBLEM 1. Sluggish heater 2. High Fuel Consumption 3. Back puffing 4. Smoke rollout w

REPLACEMENT PARTS FOR THE MODEL 81 1. Air Control Bar MF 810084 2. Door Handle Assembly PA 910096 3. Door Latch PC 910098 4. Do

NEW BUCK CORPORATION (NBC) "LIMITED WARRANTY" FOR THE BUCK STOVE PLEASE READ THIS WARRANTY CAREFULLY PRODUCTS COVERED This warranty cove

If for any reason you are dissatisfied with the suggested procedures, you may contact us in writing at: New Buck Corporation Customer Service D

EPA COMPLIANCE STATUS The Model 81 heater meets U.S. Environmental Protection Agency’s Emission limits for wood heaters sold after July 1, 1992. Und

INSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONS MODEL 81 READ THIS FIRST IMPORTANT INSTRUCTIONS WARNING THESE UNITS GENERATE A LOT OF HE

CAUTION YOUR CHIMNEY MUST BE CORRECTLY SIZED. A CHIMNEY THAT IS TOO SMALL OR LARGE IN DIAMETER OR TOO SHORT, CAN CAUSE YOUR STOVE TO SPILL SMOKE W

SECTION II MASONRY INSERT INSTALLATION The Model 81 may be installed using an all masonry fireplace built in accordance with the Uniform Buildin

MINIMUM CLEARANCES Floor Protection: When installing freestanding heater, a floor protector must be use. Floor protection must be 3/8” minimum thick

POSSIBLE TOOLS NEEDED FOR INSTALLATION If you decide to install your own stove, there are several hand tools you may need to do the job. If you do n